Опис
Інформація для замовлення
Характеристики H08RC
Характеристика | Значення |
---|---|
Входи (AI) | 8 термополегшень |
Розрядність ЦАП | 16 бит |
Інтерфейси | 1xRS485 |
Типи термополегшень | Pt100 | Pt1000 | Cu100 | Cu50 |
Роздільна здатність | 0.1℃ | |||
Вхідний опір | 6 MОм | |||
Час відгуку | 560 мс для 4 каналів, 880 мс для 8 каналів | |||
Роздільна здатність | 16 бит | |||
Точність | 0.1% от диапазона | |||
Ізоляція | оптиоізоляція аналогової частини (немає ізоляції між входами) | |||
Споживання | 24 VDC ±20%, 50 мА(Макс) |
Характеристики живлення
Характеристика | Значення |
Напруга живлення | DC24V -15%~+20% |
Споживання | 1.8VA |
Імпульс із живленням | MAX 20A 1.5 мс @24 VDC |
Пропадання живлення | Не більш ніж 10 мс |
Запобіжник | 2 A, 250 V |
Ізоляційний бар'єр | немає |
Захист живлення | Переполюсування, перевищення напруги |
Технічні умови використання
Характеристика | Значення |
Розміри | 93*95*82 мм |
Вага нетто (грам) | 353 |
Вага брутто (грам) | 455 |
Температура/Вологість | Робоча температура: 0 ~ + 55 °C; температура зберігання: - 25 ~ + 70 °C і вологість: 5 ~ 95% RH, без конденсату |
Стійкість до вібрації | 10~57 Гц 0.075mm, 57 Гц ~ 150 Гц прискорення 1G,X, Y, Z три осі 10 разів у кожному напрямку |
Стійкість до удару | 15G, тривалістю 11 мс, X, Y, Z три осі 6 разів у кожному напрямку |
Електромагнітна сумісність | AC EFT: ± 2500V, surge: ± 2500V, DC EFT: ±2500V, surge: ±1000V |
Захист від високої напруги | Між клемами AC PE 1500 VAC, 1 хв Між клемаммі DC і PE 500 VAC, 1 хв |
Опір ізоляції | Між клемами AC and PE 500 VDC >=5M Між будь-яким входом виходом і PE 500 VDC |
Габарити
93*95*82 мм
Схеми H08RC
Схема під'єднання клем
Діаграма під'єднання
Таблиця регістрів
CR Number | Function Declare |
H08RC | |
00H (Read only) | The low byte is the module code, and the high byte is the module version number. |
01H | Communication address |
02H | Communication protocol: The low 4-bit of the low bytes:0 - N,8,2 For RTU,1 - E,8,1 For RTU, 2 - O,8,1 For RTU,3 - N,7,2 For ASCII,4 - E,7,1 For ASCII,5 - O,7,1 For ASCII,6 - N,8, 1 For RTU |
The high 4-bit of the low bytes: 0 – 2400,1 – 4800,2 – 9600,3 – 19200,4 – 38400, 5 – 57600,6 - 115200 | |
03H~06H | Extend module name |
07H~08H | Default IP address: 192.168.1.111 |
09~0AH (Read only) | Reserve |
0BH | High byte subnet mask(b3~b0,1 indicates 255,0 indicates 0 , for example, subnet mask 255.255.255.0, b3~b0=1110), low byte Reserved |
0CH~0EH (Read only) | Reserve |
0FH (Read only) | Error code: 0-Normal, 1-Illegally firmware identity, 2-Incomplete firmware, 3-System data access exception, 4-No external 24V power supply |
10H (Read only) | The input value of channel 1 |
11H (Read only) | The input value of channel 2 |
12H (Read only) | The input value of channel 3 |
13H (Read only) | The input value of channel 4 |
14H (Read only) | The input value of channel 5 |
15H (Read only) | The input value of channel 6 |
16H (Read only) | The input value of channel 7 |
17H (Read only) | The input value of channel 8 |
18H | The signal type of channel 1, note 3 |
19H | The signal type of channel 2, note 3 |
1AH | The signal type of channel 3, note 3 |
1BH | The signal type of channel 4, note 3 |
1CH | The signal type of channel 5, note 3 |
1DH | The signal type of channel 6, note 3 |
1EH | The signal type of channel 7, note 3 |
1FH | The signal type of channel 8, note 3 |
20H | Use the engineering value mark, note 6 |
21H | The lower limit in engineering value of channel 1 |
22H | The lower limit in engineering value of channel 2 |
23H | The lower limit in engineering value of channel 3 |
24H | The lower limit in engineering value of channel 4 |
25H | The lower limit in engineering value of channel 5 |
26H | The lower limit in engineering value of channel 6 |
27H | The lower limit in engineering value of channel 7 |
28H | The lower limit in engineering value of channel 8 |
29H | The upper limit in engineering value of channel 1 |
2AH | The upper limit in engineering value of channel 2 |
2BH | The upper limit in engineering value of channel 3 |
2CH | The upper limit in engineering value of channel 4 |
2DH | The upper limit in engineering value of channel 5 |
2EH | The upper limit in engineering value of channel 6 |
2FH | The upper limit in engineering value of channel 7 |
30H | The upper limit in engineering value of channel 8 |
31H | The sampling frequency of channel 1, note 1 |
32H | The sampling frequency of channel 2, note 1 |
33H | The sampling frequency of channel 3, note 1 |
34H | The sampling frequency of channel 4, note 1 |
35H | The sampling frequency of channel 5, note 1 |
36H | The sampling frequency of channel 6, note 1 |
37H | The sampling frequency of channel 7, note 1 |
38H | The sampling frequency of channel 8, note 1 |
39H | The zero point correction value of channel 1 |
3AH | The zero point correction value of channel 2 |
3BH | The zero point correction value of channel 3 |
3CH | The zero point correction value of channel 4 |
3DH | The zero point correction value of channel 5 |
3EH | The zero point correction value of channel 6 |
3FH | The zero point correction value of channel 7 |
40H | The zero point correction value of channel 8 |
41H (Read only) | Channel 1~8 input disconnection, note 5 |
42H~4FH (Read only) | Reserve |
файли для роботи з H08RC
Назва | Дата оновлення | Примітка | Файл |
---|---|---|---|
Інструкція користувача температурного модуля розширення (eng) | 13/06/2017 | [pdf - 2.4MB] | Завантажити |
Застосунок HaiwellHappy V2.2.4. для програмування Haiwell PLC | 05/06/2017 | [архив rar - 27MB] | Завантажити |
Каталог продукції PLC Haiwell (eng) | 05/06/2017 | [pdf - 8.6MB] | Завантажити |
Посібник щодо застосунку HaiwellHappy для програмування ПЛК (eng) | 20/04/2017 | [chm, 4.92MB] | Завантажити |
- Ціна: Ціну уточнюйте